Smoke test running through a flue

Services

Flue pressure testing and smoke testing.

Pressure tests with a test report, and smoke tests, for commercial flues and generator exhausts. On the systems we install and on flues already in service.

At a glance

Flue testing, in short.

Pressure test
Shows a flue or exhaust is sealed before the plant runs. You get a test report.
Smoke test
Shows the smoke leaves at the terminal with no visible leakage along the route.
On our installs
A smoke test is standard on every flue we install. Pressure testing where it is in the quote or added as a variation.
On existing flues
We pressure and smoke test flues already in service. Any remedial work is recommended and agreed separately.
Real figures
2,499 Pa on a hospital generator exhaust. 3,000 Pa for 15 minutes on a hotel CHP flue.
Paperwork
A test report, and a certificate of conformity where applicable. A sample test certificate is on our downloads page.
  • 24 hours to a price, from drawings or survey information
  • 7 days to a survey, normally within a week of order
  • 60 minutes to calculations and CAD drawings after survey
  • Same day job-specific RAMS, normally
  • 2 to 4 weeks from order to install, faster when it is urgent

Normal turnarounds. How we work

When it is needed

When do you need a flue pressure test?

When the specification asks for one, when a generator or CHP exhaust has to be shown to be sealed before the engine runs on load, after a repair, or when a flue already in service looks like it is leaking.

Staining or water at a joint usually means condensate and flue gas are getting out. We survey it, put right the failed sections, seals or falls, then pressure test and give you a test report.

  • Pressure testing with a test report
  • Smoke testing on completion
  • Tests witnessed by the client or consultant
  • Test points and test tees built into new systems
  • Testing after repairs and new seals
  • Testing temporary flues during a changeover
  • Certificate of conformity where applicable

Real tests

What have real tests looked like?

At Blackpool Victoria Hospital two standby generator exhausts were pressure tested at 2,499 Pa on the final day on site, and the certificate of conformity was issued the day after.

At Furnival House in Highgate we took apart four boiler flue systems serving thirteen boilers, rebuilt them with new seals, then pressure tested each system and gave each its own test certificate.

At RAF Marham the smoke test on completion was witnessed by the client. The smoke left at the terminal with no visible leakage.

Flue pressure test rig: a fan unit with a speed controller and gauge, hosed onto a diesel engine exhaust in a plant room
Leakage test screen on the flue tester during a pressure test, showing the leak limit, barometric pressure and temperature

A pressure test on a diesel engine exhaust in September 2026: the test rig hosed onto the exhaust, and the tester's leakage test screen.

To price it

What we need to price a test.

A few details are enough. We price from them or arrange a visit.

Send what you have
  1. What it serves Boiler, generator, CHP or other plant.
  2. Size and length Flue diameter and a rough length.
  3. The test asked for The pressure and duration in your spec, if it gives one.
  4. Access Test points, and how we reach the terminal.
  5. Witnessing Whether the client or consultant wants to be there.
  6. Site Town or postcode.

Common questions

Asked about flue testing.

Anything else, call 01395 201950, email [email protected] or ask Grün AI.

  • What testing do you do?

    Pressure testing with a test report, smoke testing and CCTV surveys. Each job includes the testing agreed for the project, with test reports and a certificate of conformity where applicable.
  • Is testing included in the price?

    A smoke test is standard on every flue we install. Pressure testing is done where it’s in the quote or added as a variation, so tell us if your spec needs it.
  • Do you pressure test generator exhausts?

    Yes. The exhaust is pressure tested on completion, so the site knows it’s sealed before the generator runs on load. You get a test report, and a certificate of conformity where applicable.
  • Can you test a flue you did not install?

    Yes. We do flue inspections, condition checks, CCTV flue surveys and pressure and smoke testing on flues already in service. Any remedial work is recommended and agreed separately.
  • When do we get the test report?

    Test reports, and the certificate of conformity where applicable, come after testing. The completion report, photos and O&M pack go in your project folder at handover, normally before the engineers get home.
  • Can I see a sample test certificate?

    Yes. Our downloads page has a sample RAMS, a sample handover pack and a sample test certificate, from real jobs with client details blacked out.
  • How do I get a price for a flue pressure test?

    Send the flue size, a rough length, what it serves and the site through the contact page. We normally send a price within 24 hours.

Need a flue tested?

Send the size, the length and the site. A price normally comes back within 24 hours.

Free survey

Want us to come and look?

Free for commercial and industrial projects. We’ll call to confirm the details and the date before anything is booked.