Two stainless flue runs on wall brackets ending in roof fans on a brick hotel elevation

Services

CCTV flue surveys and condition reports.

A camera down the inside of the flue or chimney, normally from the roof terminal, and a report with photos of what we find. For facilities managers, M&E contractors and consultants.

At a glance

CCTV flue surveys, in short.

What it is
A camera survey of the inside of a flue or chimney, normally from the roof terminal down.
What it finds
Leaking joints, failed seals, dropped inner liners, corrosion, blockages and debris.
What you get
A report of what we found, with photos you can pass to your client or the building owner.
Cost
Surveys for quoting are free. Inspections and CCTV surveys are charged.
Time on site
Allow up to two hours for a survey visit.
Afterwards
We price the repair or replacement, then fit, test and certify it with our own engineers.

When it is needed

When do you need a CCTV flue survey?

When you need to know what state a flue is in before you rely on it: an old chimney you want to line, a riser you hope to reuse, a flue that has failed its service, or staining and water you cannot explain.

If you want a flue or condition report, we recommend a CCTV survey down from the top so we can see inside. On a chimney, the survey decides whether it can be lined or needs a new stack.

A survey for a quote is different. There we measure, sketch and photograph the route so we can price and draw the job, and that visit is free.

  • CCTV survey from the roof terminal down
  • Route measured, sketched and photographed
  • Flue condition and safety report with photos
  • Leak investigations with a written report
  • Checks on an old chimney before lining
  • Furnace and process exhaust surveys
  • Unsafe flues made safe on the day
  • A price for the repair or replacement

Real surveys

What have our surveys found?

At Walthamstow Academy the customer expected to reuse the existing riser. Our CCTV survey found screws and rivets through its liner, and condensate staining. We designed an external route in its place.

At Prestwick Airport two flues on a mast had failed: corroded liners, broken-down insulation and sheared brackets. We lowered about 12 m of flue to the ground, capped what was left and left the site safe. Our condition report recommended full replacement.

At the University of Birmingham we investigated a leaking boiler header. Our report found the joints had been sealed with a silicone that was not suitable for condensing boilers, and it had perished.

To book it

What we need to book a survey.

Send what you have. If you are not sure what the appliance is, a few photos will do.

Send what you have
  1. Site address And a named contact on site.
  2. The appliance Boiler, generator or other plant, and whether it is running.
  3. What you have seen Staining, water, a smell, a failed service, or nothing yet.
  4. Photos The plantroom, the flue and the terminal if you can.
  5. Access To the plantroom, the riser and the roof.
  6. Site rules Inductions, permits and anything that needs booking.

Common questions

Asked about flue surveys.

Anything else, call 01395 201950, email [email protected] or ask Grün AI.

  • Do you do CCTV flue surveys?

    Yes. We measure, sketch and photograph the route, and that feeds the drawings and RAMS. We also do flue inspections, condition checks and CCTV flue surveys, normally from the roof terminal down.
  • Is a survey free?

    Surveys for quoting are free. Inspections and CCTV surveys are charged.
  • How do you check an old chimney?

    We survey it: measure, sketch and photograph the route and check its condition. If you want a flue or condition report, we recommend a CCTV survey down from the top so we can see inside. The survey decides whether it can be lined or needs a new stack.
  • Do I get a report I can pass on?

    Yes. After the survey you get a report of what we found, with photos you can pass to your client or the building owner.
  • Our flue failed its service. What do we do?

    Send us the site address, the appliance and any photos. We survey it, normally with a camera from the terminal down, report what we find with photos, price the repair or replacement, then fit, test and certify it with our own engineers.
  • How long does a survey take?

    Allow up to two hours on site for the engineer.
  • What flue faults do you find?

    The common ones are leaking joints and failed seals, no fall on horizontal runs, staining round penetrations, terminals in the wrong place, rust and cracked weathering, failed brackets, failed insulation and dropped inner liners. Our flue faults page has photos of each.

Need a flue looked at?

Send the site address, the appliance and any photos. For anything urgent, call 01395 201950.

Free survey

Want us to come and look?

Free for commercial and industrial projects. We’ll call to confirm the details and the date before anything is booked.